hpux# dmesg [ 1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, [ 1.000000] 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, [ 1.000000] 2018, 2019 The NetBSD Foundation, Inc. All rights reserved. [ 1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993 [ 1.000000] The Regents of the University of California. All rights reserved. [ 1.000000] NetBSD 8.99.37 (GENERIC) #0: Fri May 3 16:06:56 UTC 2019 [ 1.000000] mkrepro@mkrepro.NetBSD.org:/usr/src/sys/arch/hppa/compile/GENERIC [ 1.000000] HP9000/778/B160L (Merlin L2 160) [ 1.000000] real mem = 512 MB (73728 reserved for PROM, 499 MB used by NetBSD) [ 1.000000] avail mem = 490 MB [ 1.000000] timecounter: Timecounters tick every 10.000 msec [ 1.000000] Kernelized RAIDframe activated [ 1.000000] mainbus0 (root) [flex fff80000] [ 1.000000] pdc0 at mainbus0 [ 1.000000] power0 at mainbus0: not available [ 1.000000] cpu0 at mainbus0 hpa 0xfffb0000 path 48 irq 31: PA7300LC (Velociraptor) rev 0 [ 1.000000] cpu0: PCXL2, PA-RISC 1.1e, lev 1, cat A, 250 MHz clk [ 1.000000] cpu0: shadows, 0K/0K D/I caches, 256 shared TLB, 0/0 D/I BTLBs [ 1.000000] cpu0: type 82, sv 0 floating point, rev 0 [ 1.000000] mem0 at mainbus0 hpa 0xfffbf000 path 63: viper rev 0, ctrl 0x0 size 512MB [ 1.000000] phantomas0 at mainbus0 hpa 0xffc00000 path 8 [ 1.000000] dino0 at phantomas0 hpa 0xfff80000 path 8/0: Dino V3.1 [ 1.000000] "Core RS-232C" at dino0 (type 0xa, sv 0x8c) hpa 0xfff83000 path 8/0/63 not configured [ 1.000000] pci0 at dino0 bus 0 [ 1.000000] pci0: i/o space, memory space enabled [ 1.000000] esiop0 at pci0 dev 0 function 0: Symbios Logic 53c895a (ultra2-wide scsi) [ 1.000000] esiop0: using on-board RAM [ 1.000000] esiop0: interrupting at irq 0 [ 1.000000] scsibus0 at esiop0: 16 targets, 8 luns per target [ 1.000000] wm0 at pci0 dev 1 function 0: Intel i82540EM 1000BASE-T Ethernet (rev. 0x03) [ 1.000000] wm0: interrupting at irq 1 [ 1.000000] wm0: 32-bit 33MHz PCI bus [ 1.000000] wm0: 64 words (6 address bits) MicroWire EEPROM [ 1.000000] wm0: Ethernet address 52:54:00:12:34:56 [ 1.000000] wm0: 0x200402 [ 1.000000] makphy0 at wm0 phy 1: Marvell 88E1011 Gigabit PHY, rev. 0 [ 1.000000] makphy0: Failed to access EADR. Are you an emulator? [ 1.000000] makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto [ 1.000000] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0 [ 1.000010] timecounter: Timecounter "itimer" frequency 250000000 Hz quality 100 [ 1.010816] scsibus0: waiting 2 seconds for devices to settle... [ 3.059012] cd0 at scsibus0 target 2 lun 0: cdrom removable [ 3.221513] sd0 at scsibus0 target 6 lun 0: disk fixed [ 3.262044] sd0: 8192 MB, 16383 cyl, 16 head, 64 sec, 512 bytes/sect x 16777216 sectors [ 3.565495] boot device: sd0 [ 3.636237] root on sd0a dumps on sd0b [ 3.858365] root file system type: ffs [ 3.878596] kern.module.path=/stand/hppa/8.99.37/modules [ 30.240987] esiop0: autoconfiguration error: phase mismatch without command [ 30.240987] esiop0: autoconfiguration error: unhandled scsi interrupt, sist=0x80 sstat1=0x0 DSA=0x18b2d21 DSP=0x50 [ 30.274498] esiop0: scsi bus reset [ 30.274498] cd0: async, 8-bit transfers, tagged queueing [ 30.286648] sd0: async, 8-bit transfers, tagged queueing [ 39.580214] esiop0: autoconfiguration error: phase mismatch without command [ 39.580214] esiop0: autoconfiguration error: unhandled scsi interrupt, sist=0x80 sstat1=0x0 DSA=0x1 DSP=0x50 [ 39.618554] esiop0: scsi bus reset [ 1602.858694] esiop0: autoconfiguration error: phase mismatch without command [ 1602.858694] esiop0: autoconfiguration error: unhandled scsi interrupt, sist=0x80 sstat1=0x0 DSA=0x18b2b41 DSP=0x50 [ 1602.894129] esiop0: scsi bus reset